Posted in

how to adjust the tracks on a wheeled excavator

If you’ve ever watched a wheeled excavator work a tight city job—digging around curbs, moving between sites without needing a trailer, or tucking into a backyard that no tracked machine could fit—you know how game-changing these units are. But here’s the thing that catches a lot of new operators off guard: track tension isn’t a “set-it-and-forget-it” deal. Too loose, and you’re wasting power, wearing out tracks prematurely, maybe even letting them slip off mid-lift. Too tight, and you’re stressing the wheel hubs, the idler arm, and the whole undercarriage faster than you should. As a wheeled excavator supplier, I see this mistake all the time, so let’s break down how to adjust tracks right, no guesswork required. Wheeled Excavator

First, let’s get the basics straight. Wheeled excavator tracks work a little different from the tracks on a standard dozer or crawler excavator. They’re rubber, for one thing—way more flexible, but also more prone to stretching if tension’s off. And because they’re mounted on wheels, not fixed tracks, the undercarriage has a tiny idler wheel (usually at the front or back, depending on your model) that’s the part you adjust. That’s the adjuster point, not some complicated hydraulic box hidden under the frame. But before you even touch a wrench or a grease gun, there’s a few pre-checks that’ll save you hours of headache.

Stop what you’re doing and do this first: park the machine on flat, solid ground. No slopes, no soft gravel that shifts when you lean on the tracks. Shut off the engine, set the parking brake, and chock the wheels on the non-adjusted side (wait, right—most wheeled excavators only have one adjustable track per side, so pick the one opposite the chocks to work on) to keep it from rolling. Then, grab a tape measure. The industry standard for track tension check is to measure the gap between the top of the track and the bottom of the idler wheel, right in the middle. For most 10-15 ton wheeled excavators, that gap should be between 20mm and 30mm—about the thickness of a standard smartphone. If it’s way bigger, your track’s loose; smaller, and it’s too tight. Pro tip here: don’t check this right after you’ve run the machine hard for an hour. Tracks stretch when warm, so adjust them when the engine’s cold, after letting the machine sit overnight. That way, your measurement’s accurate, not skewed by thermal expansion.

Now, the actual adjustment process. Let’s walk through it step by step, plain and simple. First, find the grease fitting on the idler arm. On most models, it’s a big, zerk-style fitting right on the end of the idler, where the adjuster cylinder meets the frame. You’ll need a grease gun—standard heavy-duty one, not a tiny DIY job—and a wrench to hold the idler arm steady while you grease. Here’s how it works: pumping grease into the fitting pushes the idler wheel outward, away from the drive sprocket, which pulls the track tighter. To loosen a track, you just reverse it: you’ll usually find a small bleed valve next to the grease fitting, crack that open, and the hydraulic pressure pushes grease back out, letting the idler move inward.

Wait, let’s make that specific, because messing up the bleed valve can leave you with a loose track and grease all over your boots. When you’re adjusting tension, do small, short grease pumps, not a whole can at once. Every 2-3 pumps, stop, measure the gap, and test the track. How do you test it? Grab the top of the track with both hands and pull up as hard as you can. If you can lift it more than 50mm (about two inches), it’s way too loose. If you can barely move it, it’s too tight. That quick test is a good double-check for the tape measure. Also, if you’re adjusting the left track, do the same for the right—tracks stretch evenly, so both sides need the same tension, otherwise the machine will pull to one side when you’re driving or digging.

I’ve seen way too many new operators over-tighten tracks because they think tighter is better. Don’t do that. Tight tracks put extra stress on the idler arm, the wheel bearings, and even the hydraulic system that moves the idler. Over time, that leads to costly repairs—replacing a wheel hub on a wheeled excavator is way more expensive than a quick track adjustment. Also, too-tight tracks cause unnecessary friction, which makes your engine work harder, uses more fuel, and wears out the track itself faster. A properly tensioned track only has enough pull to keep it from slipping off the sprocket when you’re digging or moving over uneven ground.

Now, how often should you adjust tracks? It’s not a one-time thing. Every 50 hours of operation is a good rule of thumb, but adjust it more often if you’re working in harsh conditions: mud, gravel, steep slopes, or if you’re towing the machine on a trailer (wait, towing can stretch tracks! So always check tension before you load it on a truck). Also, if you notice the machine pulling to the left or right when you’re driving in a straight line, that’s a sign one track is tighter than the other. Or if you hear a clunking noise coming from the undercarriage when you move, that’s probably a loose track slipping around the sprocket. Don’t ignore that—if a track slips off, you’re stuck on a job site, and getting it back on is a pain, especially if you’re in a tight spot like a downtown street.

Wait, one common mistake: not cleaning the track before you adjust. If you’re working in mud or clay, the track can pack with material, which makes it thicker, so your measurement will be wrong. Before you do any tension check, spray the track down with a pressure washer (low pressure, don’t blast the rubber) to get rid of all the mud and debris. That way, your tape measure is measuring the actual track, not extra gunk on top. I learned that the hard way—once, a customer brought their machine to us saying the track was too loose, and when we pressure washed it, the gap shrank 15mm just from the mud coming off. Saved them from an unnecessary adjustment.

Another thing: when you’re done adjusting, make sure you top off the grease fitting. If you leave it low, dirt and grit can get in, which will wear out the fitting and the idler arm faster. Wipe up any excess grease too—grease on the track or wheels will make the machine slippery, which is a safety hazard.

Now, let’s talk about when you might need to replace a track instead of just adjust it. Tracks have a lifespan, usually around 1000-1500 hours, depending on use. If you measure the track’s stretch: a new track is about 1500mm long, and when it’s stretched past 1550mm, it’s time for a new one. If you keep adjusting a track that’s already stretched too much, it’ll just keep getting looser, and eventually you’ll have to replace it anyway, plus risk damaging the undercarriage. As a wheeled excavator supplier, we offer replacement tracks for all our models, and we always tell customers to inspect tracks at every 100 hours to catch wear early.

Let me wrap this up with a quick recap, so you don’t forget: 1. Park on flat ground, chock wheels, engine off, cold for accurate measurements. 2. Clean debris off tracks. 3. Measure the gap between idler and track, aim for 20-30mm. 4. Use small grease pumps, check often, don’t over-tighten. 5. Adjust both tracks evenly, test tension by pulling up on the track. 6. Clean up excess grease, check tension regularly.

If you’re in the market for a reliable wheeled excavator, or you need replacement tracks or undercarriage parts for the one you already have, don’t hesitate to reach out to our team. We’re not just suppliers—we’re operators too, so we know how important it is to keep your machine running smooth, no hassle.

Crane References:

  1. International Organization for Standardization. (2020). Earth-moving machinery – Wheeled excavators – Under-carriage maintenance and adjustment guidelines. ISO 13110:2020.
  2. Construction Equipment Association. (2022). Maintenance Best Practices for Wheeled Excavator Undercarriages. CEA Technical Bulletin 18-22.
  3. Caterpillar Inc. (2021). Wheeled Excavator Operator’s Manual: Under-carriage Adjustment. CAT Publication SEBD0892.
  4. Komatsu Ltd. (2021). Wheeled Excavator Track Tension and Wear Maintenance Guide. Komatsu Technical Note WEX-TRK-01.

Best Heavy Industry (Shandong) Co., Ltd.
As one of the most professional wheeled excavator manufacturers and suppliers in China, our products have good reputation in the market. Please feel free to buy premium wheeled excavator made in China here from our factory. Quality products and reasonable price are available.
Address: Quanpu Industrial Park, Liangshan County, Jining City, Shandong Province.
E-mail: ensonzhouau@gmail.com
WebSite: https://www.trustmytrucks.com/