Posted in

How to reduce injection mold injection pressure?

If you’ve spent any time working with injection molds, you know that injection pressure is a make-or-break factor for part quality, cycle times, and long tool life. Too little pressure, and you get short shots, sink marks, or warped parts that get rejected on the production line. Too much pressure, and you’re risking cracked mold cores, stretched ejector pins, or even a complete tool failure that costs you days of downtime. As someone who’s been supplying custom injection molds to manufacturers for over 12 years, I’ve walked customers through this exact challenge hundreds of times. Today, I’m pulling back the curtain on the scientific, practical ways to lower injection pressure without sacrificing part integrity or production speed. Injection Molds

Let’s start with a quick primer on why injection pressure matters for anyone using or manufacturing with molds. Injection pressure is the force the molding machine exerts to push molten plastic through the sprue, runner system, and into every corner of the mold cavity before it cools. For complex parts—think of a automotive dashboard trim or a medical device with tiny hinges—pressure needs to be precise enough to fill those small features without overloading the tool. When I first started in the mold supply business, many customers would crank the pressure dial higher as a default fix for filling issues, not realizing that small adjustments upstream would eliminate the need for that extra force. That was a mistake I learned to correct early on.

One of the most impactful ways to reduce injection pressure is simple: optimize the melt temperature of your plastic. It sounds counterintuitive—warm plastic is less viscous, right? The hotter the melt, the easier it flows. But here’s the science: for every 10°C (18°F) increase in melt temperature, many common thermoplastics (like polypropylene, ABS, or polyethylene) see a 10-20% drop in viscosity. That means you can push that molten material through the mold with far less force than if it’s cold and thick. The key here is not to crank the temperature too high—overheating can cause material degradation, which leads to discoloration, brittleness, or gas bubbles in the part. For example, if you’re molding polypropylene for packaging, running it at 220°C instead of 200°C will cut your required injection pressure by roughly 15%, according to standard material data sheets. I always tell customers to test melt temperature in small increments, holding it for 10 cycles to ensure no degradation, before dialing it up.

Next up: redesigning the runner system. This is where my background as a mold supplier really comes in. The runner system—those channels that carry plastic from the machine’s nozzle to each cavity— is a major source of pressure loss. Every time plastic has to turn a corner, narrow, or travel a long distance, you lose pressure. For single-cavity molds, shortening the runner length can drop pressure requirements by 10-15% immediately. For multi-cavity molds, common in high-volume production, balanced runner design is non-negotiable. Too many shops cut corners on balanced runners to save material costs, which means some cavities get plastic too early (needing more pressure to fill) and others starve. We’ve reworked dozens of customer’s old runner systems: changing from a cold runner to a hot runner (for molds producing millions of parts a year) can reduce injection pressure by 25-30% because hot runners keep plastic molten longer, eliminating the need to push through cooled material in standard runners. Even small tweaks, like making runners slightly larger (as long as they don’t increase cycle time by holding extra material) can cut pressure needs. A customer who made plastic bottle caps brought us a mold that required 1200 psi of injection pressure; we adjusted the runner size and balanced the system, and they dropped that to 850 psi, reducing mold wear and part reject rates.

Another often-overlooked fix: improving mold venting. When plastic is injected into the cavity, air has to escape—if it can’t, it creates resistance that forces you to use higher pressure to push the plastic past. Poor venting is one of the top causes of excessive pressure in molds I see, and it’s easy to fix without a full tool redesign. Adding vents along the parting lines, around core pins, and at the farthest point of the cavity lets air escape as the plastic fills. Vents should be 0.025-0.05 mm deep (depending on the plastic’s viscosity) and wide enough to cover the area, but not so deep that plastic leaks out. For a customer molding small electronic connectors, we added 0.03 mm deep vents along the edge of the 0.5 mm thick connector; their injection pressure dropped from 1000 psi to 700 psi, and they eliminated the voids that were causing 8% of parts to fail inspection. I always tell new customers: if you’re fighting high pressure, check vents first—you might not need to change anything else.

Material selection is a big one too. Not all plastics flow the same. Some high-flow grades (like PP homopolymer or high-MFI ABS) are designed to fill complex molds with lower pressure, while lower-flow grades (like glass-filled nylon or PEEK) need much more force to move. If a customer is using a low-flow plastic for a part that doesn’t require extra strength, switching to a high-flow grade can drastically cut injection pressure. For example, a customer molding a 5 mm thick plastic bracket was using 30% glass-filled nylon, which required 1800 psi; switching to a high-flow unfilled nylon cut that to 1100 psi, and the part still met their strength requirements for the application. The tradeoff here is that high-flow materials might have slightly lower impact resistance, but for many structural parts, it’s a viable alternative that saves pressure and reduces mold stress.

Ejector system design and machine setup also play a role, surprisingly. If ejector pins are sticking or the mold is misaligned, the machine will need extra pressure to push the part into place, which can bleed over into the injection phase. Keeping mold surfaces lubricated (with mold-safe lubricants, not general oils) and ensuring ejector pins move freely reduces friction, which lowers overall force requirements. On the machine side, using the correct injection speed is important: too fast, and the plastic doesn’t have time to flow smoothly, creating turbulence that increases pressure; too slow, and the plastic starts to cool before filling, requiring higher pressure to finish. Finding the optimal fill time—usually between 0.5 and 3 seconds for most parts—lets plastic fill evenly with minimal force.

Wait, let’s talk about something that’s close to my work as a mold supplier: tool material and finish. When a mold has a rough surface finish, the plastic has to push against more friction as it flows through the cavities and runners. Polishing the cavity and runner surfaces to a mirror finish (or at least a Ra of 0.2 um for most applications) reduces friction, so less pressure is needed. Even using a mold material with lower surface energy, like chrome-plated steel, can help. For a customer making medical implants that required a polished mold, we chrome-plated the cavities and runners; their injection pressure dropped 20%, and they also saw less part sticking to the mold, which cut cycle time.

Now, it’s important to note that none of these changes are one-size-fits-all. A part that’s thin and complex will need different adjustments than a thick, simple part. That’s why I always recommend working with a mold supplier who can do a flow simulation before you build or modify a mold. Flow simulation software lets you test melt temperature, runner design, and venting in a digital environment, so you can see exactly how much pressure will be needed before you spend money on tool changes. We run flow simulations for every custom mold we build, which means we’re designing for minimum injection pressure from the start, not just adding it as a fix later.

I’ve seen too many companies spend thousands of dollars on mold repairs or higher-powered molding machines because they didn’t explore these smaller, cheaper adjustments first. Let’s recap: optimize melt temperature (increase within safe limits), redesign or balance runners, improve mold venting, switch to a higher-flow material where possible, adjust ejector and machine speed, and polish mold surfaces. Each of these steps can contribute to lower injection pressure, which leads to longer mold life, lower energy costs (since the machine uses less force), and fewer defective parts.

If you’re currently dealing with high injection pressure, or you’re designing a new mold and want to avoid this issue, reach out. As an injection molds supplier, I can help you evaluate your current setup, run flow simulations, or design a custom mold from the ground up with pressure efficiency in mind. Don’t let excessive pressure eat into your production profits or cause unplanned downtime—let’s work together to find the right solution for your parts.

Injection Molds References

  1. Rosato, D. V., & Rosato, M. G. (2000). Injection Molding Handbook. Kluwer Academic Publishers.
  2. Giles, H. F., Wagner, J. R., & Balhoff, D. T. (2005). Extrusion: The Definitive Processing Guide. William Andrew Publishing.
  3. International Organization for Standardization. (2018). ISO 11469:2018, Plastics—Generic identification and marking of plastics products.
  4. Kamal, M. R., & Khayat, R. E. (1998). Rheology and Processing of Polymer Composites. Hanser Gardner Publications.
  5. Manufacturing Engineering Society International. (2021). Injection Molding Best Practices: Reducing Cycle Time and Defects. SME.

Huizhou Jiejin Plastic Technology Co., Ltd.
Huizhou Jiejin Plastic Technology Co., Ltd. is one of the most professional injection molds manufacturers and suppliers in China, featured by quality products and low price. We warmly welcome you to wholesale advanced injection molds made in China here from our factory. If you have any enquiry about customized service and OEM service, please feel free to email us.
Address: Guangming Village, Tongqiao Town, Huizhou City, Guangdong Province, China
E-mail: info@jiejinplastic.com
WebSite: https://www.jiejinplastic.com/